Water Treatment Plant, WTP Plant

Mobile Seawater RO Desalination Plant Service in Bangladesh

Mobile Seawater RO Desalination Plant

A mobile seawater RO desalination plant turns salty seawater or saline river water into safe drinking water, on site, inside a container, trailer or skid that can be moved where water is needed. For coastal Bangladesh, islands, disaster zones and remote project sites, it is one of the fastest ways to get safe water without waiting years for a fixed water treatment plant.

In this guide, PureLife explains everything in plain words: how a mobile seawater reverse osmosis (SWRO) plant works, what it costs to run, which standards the water must meet in Bangladesh, how to choose the right size, and how our team can survey, supply, install and maintain one for you anywhere in the country.

Quick answer

A mobile seawater RO desalination plant is a ready-built, transportable water treatment system. It pumps seawater or saline water through filters, then pushes it at very high pressure (about 55–70 bar) through reverse osmosis membranes that hold back salt. The output is fresh drinking water with low TDS, plus a salty reject stream (brine). In Bangladesh, these plants are used in coastal districts like Satkhira, Khulna, Bagerhat, Barguna, Patuakhali, Bhola and Cox’s Bazar, on islands, at construction and port sites, and after cyclones and floods.

Key facts at a glance (2026)

  • About 20 million people on Bangladesh’s coast cannot safely drink the water around them (Mongabay, July 2026).
  • Bangladesh’s drinking water standard allows a maximum TDS of 1,000 mg/L and chloride of 150–600 mg/L (DPHE). Seawater is far above this.
  • A seawater RO plant typically needs a high-pressure pump at 55–70 bar and recovers up to about 50% of feed water as fresh water (Frontiers in Sustainable Cities).
  • One shipping-container SWRO unit can produce up to 2,000 m³ (2 million litres) per day, enough for up to 8,000 people (Danfoss).
  • Worldwide, more than 22,000 desalination plants were running in 2024 (EU Blue Economy Observatory).

In this guide: what a mobile SWRO plant is · why Bangladesh needs it · how it works · parts and specs · types · uses · water standards · comparisons · cost · how to choose · maintenance and brine · PureLife service · FAQs.

What Is a Mobile Seawater RO Desalination Plant?

A mobile seawater RO desalination plant is a complete water purification system built on one movable base. Everything sits together: intake pump, pre-filters, high-pressure pump, RO membranes, dosing system, disinfection and control panel. You connect three lines (seawater in, fresh water out, brine out) and power, and it starts producing water.

Let us break the name into simple parts:

  • Mobile means it can be moved by truck, trailer, boat or crane. It does not need a permanent building.
  • Seawater means it is designed for very salty water, around 35,000 mg/L of dissolved salt in open oceans.
  • RO (reverse osmosis) is the process. Water is pushed through a thin membrane that lets water pass but blocks salt, bacteria and most other impurities.
  • Desalination simply means removing salt from water.

Seawater RO (SWRO) vs brackish water RO (BWRO)

Not all salty water is the same. In Bangladesh, many tube wells, ponds and rivers are brackish: saltier than fresh water but much less salty than the sea. A brackish RO plant works at lower pressure and uses less power. A seawater RO plant uses stronger membranes, pressure vessels and pumps built for high pressure.

PointBrackish water RO (BWRO)Seawater RO (SWRO)
Typical feed salt (TDS)about 1,000–10,000 mg/Labout 15,000–45,000 mg/L
Operating pressurelower (roughly 10–25 bar)high (about 55–70 bar)
Recovery (fresh water out of feed)higher, often 60–85%lower, up to about 50%
Energy uselowerhigher (about 3–4.5 kWh per m³)
Best forsaline tube wells, ponds, upstream riversopen sea, estuaries, islands, very saline rivers in dry season

Why does this matter in Bangladesh? Because coastal water changes with the season. The Bay of Bengal is less salty than most seas, as huge rivers pour fresh water into it. Studies show open-sea surface salinity in the Bay of around 33–34 psu in spring and as low as 24–32 psu in other seasons (Sengupta et al.). Near-shore and river water also gets much saltier in the dry months. So a good mobile plant for Bangladesh should be designed for the worst season (March–May), not the average.

Mobile plant vs fixed desalination plant

A fixed plant is built in a plant room with civil work, a permanent intake and pipelines. It suits a large town supply over 20 years or more. A mobile plant is factory-built and tested, then delivered ready to run. It suits sites where speed, flexibility or short-term need matter more than very large output.

In short: choose mobile when you need water fast, need to move it later, or cannot build a plant room. Choose fixed when demand is large, stable and permanent.

Why Bangladesh Needs Mobile Seawater Desalination in 2026

Salt is now the biggest drinking water problem on Bangladesh’s coast, and it is getting worse every year. Here is what the latest reports say.

1. Millions of people drink saline water every day

Around 42 million people live in Bangladesh’s coastal regions (Mongabay, 2026). About 20 million of them cannot safely drink the water around them. A UNDP survey found that 73% of residents in five coastal sub-districts of Satkhira drink saline water every day (Mongabay, 2026).

2. Salt is moving further inland and deeper underground

River salinity has spread 70 to 100 km upstream in the southern region. In March 2026, researchers from the Soil Resource Development Institute (SRDI) tested deep tube wells of 1,000 to 1,200 feet in coastal areas and found abnormal salinity in groundwater (Prothom Alo). This matters a lot: deep tube wells were long seen as the safe option.

Research estimates that about 1.5 million hectares of land have been salinized over three decades, and sea level along the coast could rise by about 32 cm by 2050 (Mongabay). A World Bank economist has warned that 2.9 to 5.2 million poor people in the southwest coast may face serious river salinity problems by 2050 (World Economic Forum).

3. Salty water harms health

Salt in drinking water is not only a taste problem. A study in the journal Elementa found that people drinking slightly saline water (1,000–2,000 mg/L) were 17% more likely to have high blood pressure (Mongabay). Research also links high-salt drinking water with preeclampsia, a dangerous pregnancy condition (Mongabay).

4. Cyclones and tidal surges destroy freshwater in hours

One cyclone or tidal surge can fill freshwater ponds with seawater overnight. On St Martin’s Island, tidal surges have contaminated freshwater ponds and damaged freshwater sources (The Daily Star). After Cyclone Remal in May 2024, 9 mobile treatment plants were sent to Barisal, Barguna, Pirojpur, Satkhira, Khulna and Bagerhat (UN Bangladesh Situation Report). During the August 2024 floods, DPHE’s 8 mobile treatment plants supplied 148,909 litres of safe water in Feni, Moulvibazar, Noakhali and Cumilla (BSS).

This is exactly the job mobile plants are built for: arrive fast, use the water that is there, and produce safe drinking water within hours.

5. Fixed solutions cannot reach everyone in time

The government and NGOs are investing in RO plants. PKSF has installed 83 desalination plants on the coast and plans more than 500 solar-powered RO plants for Satkhira, Khulna and Bagerhat (BSS, Sept 2025). Its Adaptation Fund-supported Safe Water Project (US$5 million) targets 180 RO plants for 180,000 people (PKSF). UNICEF has also built a climate-resilient desalination plant in Cox’s Bazar that makes 4,000 litres per hour (UNICEF Bangladesh).

These are big steps, but the need is far larger. Islands, chars, construction camps, ports, resorts, shrimp farms and cyclone shelters often need their own water source now. A mobile seawater RO plant fills that gap.

How a Mobile Seawater RO Plant Works: Step by Step

A mobile SWRO plant cleans water in stages. Each stage protects the next one, so the expensive RO membranes last longer. Here is the full process in simple words.

  1. Seawater intake. A submersible or surface pump draws water from the sea, river, creek or a beach well. A beach well is often better, because the sand filters the water naturally and keeps out mud and plastic.
  2. Coarse screening and disc filter. Large particles, leaves, shells and sand are caught first.
  3. Multimedia (sand) filter. Layers of sand, gravel and anthracite remove mud and turbidity. Bangladesh coastal water is often very muddy in the monsoon, so this stage is important.
  4. Ultrafiltration (optional but recommended). A UF membrane removes very fine particles, bacteria and colloids. It gives much cleaner feed water to the RO membranes, which reduces cleaning and replacement.
  5. Chemical dosing. Antiscalant stops salts from forming scale on the membranes. If chlorine is used against algae, sodium bisulfite removes it before RO, because chlorine damages RO membranes.
  6. Cartridge (micron) filter. A 5-micron filter is the last guard before the high-pressure pump.
  7. High-pressure pump. This is the heart of the plant. It raises pressure to about 55–70 bar, which is higher than the natural osmotic pressure of seawater (Frontiers in Sustainable Cities).
  8. Energy recovery device (ERD). The brine leaving the membranes is still at high pressure. An ERD (pressure exchanger or turbocharger) transfers that pressure back to the incoming water. Adding an ERD is the single most effective way to cut energy use in an SWRO plant (Danfoss).
  9. SWRO membranes. Water passes through spiral-wound seawater membranes inside pressure vessels. Fresh water (permeate) comes out one side. Salty brine comes out the other.
  10. Post-treatment and remineralisation. RO water is very pure and can taste flat. A remineraliser (calcite filter) adds back some calcium and adjusts pH so the water is healthy and does not corrode pipes.
  11. Disinfection. UV light and/or a small chlorine dose make sure no germs grow in tanks and pipes.
  12. Storage and distribution. Clean water goes to a tank, water ATM, jar-filling station or pipe network.
  13. Brine discharge. The salty reject water is sent back to the sea through a diffuser, away from the intake, following Department of Environment rules.

A smart PLC control panel runs the whole system. It watches pressure, flow, conductivity (salt level) and tank level, and it shuts down safely if something goes wrong. Many modern units also allow remote monitoring by mobile phone.

Main Components and Technical Specifications

The table below shows the parts of a typical mobile SWRO plant and what to check in each. Exact sizes depend on your water test and daily demand.

ComponentWhat it doesWhat to check
Intake pumpDraws seawater or saline waterCorrosion-resistant body (duplex steel or plastic), correct head and flow
Disc / media filterRemoves sand, silt and turbidityBackwash system, filter vessel material (FRP)
Ultrafiltration (UF)Removes fine particles and bacteriaMembrane brand, automatic backwash
Antiscalant dosingPrevents scale on RO membranesDosing pump accuracy, chemical type
Cartridge filterFinal 5-micron protectionEasy-change housing, spare cartridges
High-pressure pumpRaises pressure to about 55–70 barEfficiency, seawater-grade materials, VFD control
Energy recovery deviceRecovers pressure from brinePressure exchanger or turbo type
SWRO membranes and pressure vesselsRemove saltSeawater-rated elements, salt rejection, vessel pressure rating
RemineraliserAdds minerals, corrects pHCalcite media, pH after treatment
UV / chlorinationKills germsUV lamp life, dose control
PLC control panelRuns and protects the plantConductivity, pressure and flow sensors, alarms, remote access
Container / skid / trailerHolds and protects the systemAnti-corrosion paint, ventilation or AC, lifting points
Power supplyGrid, generator, solar or hybridLoad in kW, backup

Typical performance ranges

ItemTypical rangeSource
Operating pressure55–70 barFrontiers
Recovery (single pass)up to about 50%Frontiers
Product water TDS (single pass)about 300–500 mg/LFrontiers
Energy use (whole plant)about 3.75–4.5 kWh per m³Frontiers, PMC study
Containerised unit outputsmall units of tens of m³/day up to 2,000 m³/day per containerDanfoss

Simple capacity guide. Plan for about 3–5 litres per person per day for drinking and cooking only. For full household use, demand is much higher. As an example, a 1 m³/hour (1,000 litres per hour) plant running 20 hours gives 20,000 litres a day. That covers drinking and cooking water for roughly 4,000–6,000 people. Always add a safety margin of 20–30% for peak days.

Types of Mobile Seawater RO Plants

There is no single “mobile plant”. The right type depends on where it will go, how often it moves and how much water you need.

1. Containerised SWRO plant

The whole system is built inside a 10-, 20- or 40-foot steel shipping container. The container is also the shipping box, so it arrives fully assembled and tested. Containerised plants are plug-and-play and can be running within days of arrival (Danfoss). Best for: islands, ports, resorts, power plant sites, long-term coastal supply.

2. Trailer-mounted SWRO plant

The plant sits on a road trailer, often with its own diesel generator. It can be towed to a new site in hours. Trailer-mounted seawater RO units have already been built for UN military disaster relief in Bangladesh, giving a combined 132 gallons per minute of drinking water (Applied Membranes). Best for: cyclone and flood response, army and navy camps, moving construction work.

3. Skid-mounted SWRO plant

All parts are fixed on a steel frame (skid) that a crane or forklift can lift. It can go into an existing room, a shed or onto a boat deck. Skids are usually cheaper than containers, but need a roof and protection from rain and salt air. Best for: factories, hatcheries, hotels and sites that already have a shed.

4. Solar or solar-hybrid mobile RO plant

Solar panels power the plant in daytime, with grid, battery or generator backup. In Satkhira, solar RO plants run on a mix of solar, grid and battery power when sunlight fades (Eco-Business). Best for: off-grid villages, chars and islands where power cuts are common.

5. Boat or barge-mounted plant

A compact SWRO unit is installed on a vessel. It can serve many small islands and riverside villages in turn. Best for: char areas, river islands and rescue operations.

6. Portable emergency RO units

These are small units (often below 1 m³/hour) that two to four people can carry. They are for first response, field hospitals and rescue teams, when trucks cannot reach the site.

TypeMobilityTypical use in BangladeshSetup time
ContainerisedTruck or shipIslands, ports, resorts, project sitesDays
Trailer-mountedTowed by vehicleCyclone and flood relief, campsHours
Skid-mountedCrane or forkliftFactories, hatcheries, hotelsDays
Solar-hybridTruck, then semi-fixedOff-grid villages, charsDays to weeks
Boat-mountedMoves by waterRiver islands, char villagesReady on arrival
Portable emergencyCarried by handFirst response, field hospitalsHours

Who Needs a Mobile Seawater RO Plant in Bangladesh?

Any place near salty water that needs safe water quickly, or for a limited time, is a good fit. These are the most common users we see.

Coastal communities and union parishads. Villages in Satkhira, Khulna, Bagerhat, Barguna, Patuakhali, Pirojpur, Bhola, Noakhali, Chattogram and Cox’s Bazar can run a community water point or water ATM from one mobile plant. Water can be sold at a low price per litre to cover running costs, as many NGO plants already do.

Islands and chars. St Martin’s Island, Hatiya, Sandwip, Kutubdia, Moheshkhali and many chars have very few freshwater aquifers. A containerised plant can be shipped by boat and placed close to the shore.

Disaster response teams. Government departments, NGOs, the armed forces and UN agencies need units that move with the emergency. As we saw after Cyclone Remal, mobile treatment plants are now a normal part of the response.

Construction and infrastructure projects. Ports, power plants, bridges, embankments, economic zones and offshore projects need water for workers’ camps and, often, for concrete and process use. A mobile plant can move to the next site when work ends.

Hotels, resorts and tourism. Coastal resorts in Cox’s Bazar, Kuakata and Teknaf need steady, good-tasting water for guests, kitchens and laundry, even in the dry season.

Shrimp, fish and crab hatcheries. Hatcheries need clean water with controlled salinity. RO water can be blended with seawater to get the exact salinity needed.

Army, navy, coast guard and border camps. Remote camps on the coast and islands need a reliable, self-contained supply.

Industries on the coast. Factories in coastal zones need low-TDS water for boilers, cooling towers and processing. Seawater RO can feed a second-stage RO or demineralisation system for boiler feed water. See our guide to boiler water treatment in Bangladesh.

Schools, hospitals and cyclone shelters. These need safe water every day and even more during disasters. A small solar-hybrid unit can serve hundreds of students or patients.

Ships, offshore platforms and fishing fleets. Compact skid units produce fresh water on board, so vessels do not need to carry it from shore.

Drinking Water Standards: Bangladesh vs WHO

A desalination plant is only good if its water meets the standard. In Bangladesh, the drinking water standards are set under the Environment Conservation Rules (ECR), which were updated in 2023 and took effect on 5 March 2023, replacing the 1997 rules (UNEP LEAP, RMG Bangladesh). DPHE publishes the main values alongside WHO guidance.

ParameterBangladesh standardWHO guidanceWhy it matters for desalination
TDS1,000 mg/LNo health value; below about 600 mg/L tastes goodMain measure of salt removal
Chloride150–600 mg/L—Salty taste, pipe corrosion
Sodium200 mg/L—Linked to blood pressure
Boron1.0 mg/L—Seawater has boron; some single-pass RO may need a second pass
pH—6.5–8.5RO water is often acidic; needs remineralisation
Hardness (as CaCO₃)200–500 mg/L—RO water is very soft; minerals are added back
Iron0.3–1.0 mg/L—Common in coastal groundwater
Manganese0.1 mg/L—Common in groundwater
Arsenic0.05 mg/L0.01 mg/LRO removes most arsenic
Turbidity10 NTU—Pre-treatment must handle muddy water
Faecal coliform0 per 100 mL0Disinfection after RO is a must

Sources: DPHE – Water Quality Parameters, Bangladesh Standards and WHO Guidelines; WHO palatability guidance via Australian Drinking Water Guidelines (NHMRC); WHO chemical fact sheet on TDS.

What this means for you. A well-designed SWRO plant should deliver water well below the Bangladesh TDS limit of 1,000 mg/L. A good target for drinking water is below 500 mg/L, with pH between 6.5 and 8.5 and zero faecal coliform. Ask your supplier for a written guarantee of product water quality, based on your own raw water test, and test the output again after commissioning.

We always recommend a full raw water test from a recognised lab before design. Seawater, estuary water and coastal groundwater can each contain different problems, such as high iron, boron, oil, or bacteria, and each needs a different pre-treatment.

Mobile SWRO vs Other Coastal Water Solutions

Coastal Bangladesh uses several ways to get safe water. Each has a place. This comparison helps you decide when a mobile seawater RO plant is the right choice.

SolutionRemoves salt?Works in dry season?Speed to set upCan move?Best for
Mobile seawater RO plantYes, even seawaterYesHours to daysYesIslands, disasters, project sites, coastal businesses
Fixed seawater RO plantYesYesMonths to yearsNoLarge towns, permanent supply
Brackish water RO plantYes, for moderate saltYes, if feed salt stays moderateWeeksUsually noSaline tube wells, upstream areas
Pond sand filter (PSF)NoOnly if pond stays freshWeeksNoVillages with protected freshwater ponds
Rainwater harvestingNot needed (rain is fresh)Only with large storageDaysPartlyHouseholds, schools
Managed aquifer recharge (MAR)Dilutes salt over timeYes, once workingMonthsNoLong-term village supply
Bottled or jar waterYes (bought in)YesImmediateYesShort term only; costly for families

The simple rule: if the only water nearby is seawater or very salty river water, and you need safe water quickly or at more than one location, a mobile SWRO plant is usually the most practical option. If your water is only slightly saline, a brackish water RO plant costs less to run. Many projects combine both: rainwater in the monsoon, and RO in the dry months.

Researchers and NGOs working in the coast also use pond sand filters, managed aquifer recharge and rainwater harvesting alongside desalination (Kathy & Alam, Emerald). No single method fits every village. A water test and a short site survey will show which mix works for you.

Mobile Seawater RO Plant Price in Bangladesh: What Decides the Cost?

There is no fixed price list for a mobile seawater RO plant, because every site is different. The price depends on your water, your daily demand and how mobile the unit must be. PureLife gives a firm quotation after reviewing your water test and site discussion. Call 01919-998881 for a quote.

What affects the purchase price (CAPEX)

  • Capacity. Litres per hour or cubic metres per day. Bigger plants cost more in total but less per litre.
  • Feed water salt level. True seawater needs seawater-rated membranes, vessels and pumps. Saline river or estuary water may allow a lighter design.
  • Pre-treatment needs. Very muddy, oily or algae-rich water needs extra filtration or ultrafiltration.
  • Type of mobility. A container with AC and insulation costs more than an open skid. A trailer with its own generator costs more again.
  • Energy recovery device. It adds upfront cost but saves a lot of electricity every year.
  • Power system. Solar panels, batteries or a generator can add a large share to the total.
  • Automation level. Simple manual panel vs full PLC with remote monitoring.
  • Materials. Seawater eats ordinary steel. Duplex stainless steel, FRP and high-grade plastics last longer but cost more.
  • Storage and distribution. Tanks, water ATMs, jar-filling or pipe networks.

What affects the running cost (OPEX)

Electricity is the biggest running cost. In some SWRO plants, energy can be up to 86% of the total cost of ownership, depending on design and local tariffs (Danfoss). Other costs are membranes (replaced every few years), cartridge filters, antiscalant and cleaning chemicals, UV lamps, operator salary and routine service.

Quick way to estimate daily power use:

\text{Daily kWh} = \text{Water produced per day (m}^3\text{)} \times \text{Energy use (kWh per m}^3\text{)}

Example: a plant making 20 m³ (20,000 litres) a day at about 4 kWh per m³ uses about 80 kWh a day. Multiply by your electricity or diesel cost per kWh to get the daily energy bill. Divide by 20,000 to get the energy cost per litre.

Community water pricing. Many coastal community RO plants recover running costs by selling water at a very low price. For example, a PKSF-funded plant in the coast sells water at Tk 0.5 per litre (The Business Standard). A clear business model like this keeps a plant running for years.

Buy, rent or service contract?

OptionBest whenNote
Buy the plantLong-term need, own operatorAdd an annual maintenance contract (AMC)
Rent or leaseShort projects, disaster season, trialsFaster approval, no large upfront cost
Build-operate serviceYou want water, not a machineSupplier runs the plant, you pay for water or a monthly fee

Ask us which of these options suits your budget and project timeline.

How to Choose the Right Mobile Seawater RO Plant: 12-Point Checklist

Use this checklist before you buy or rent. It will save you from the most common and costly mistakes.

  • Test the raw water first. Get TDS, chloride, iron, boron, turbidity, oil and bacteria tested. Test in the dry season too, when salt is highest.
  • Know your daily demand. Count people, litres per person and any process water. Add 20–30% margin.
  • Decide how mobile it must be. Will it stay at one site for years, or move every few weeks?
  • Check the power source. Is there stable grid power? If not, plan for a generator, solar or hybrid system.
  • Ask for the energy use per m³. A good SWRO plant with an energy recovery device should be in the range of about 3–4.5 kWh per m³.
  • Ask for the recovery rate. For seawater, about 35–50% is normal. Very high claims for true seawater are a warning sign.
  • Check membrane and pump brands. Ask for data sheets, warranty and where spares are stocked in Bangladesh.
  • Check materials. All wet parts on the high-pressure side should be seawater-grade (duplex steel or suitable plastics).
  • Ask for a product water guarantee. It should state TDS, pH and microbiological quality in writing.
  • Plan brine disposal. Where will the salty reject water go, and is it allowed by the Department of Environment?
  • Ask about training and after-sales service. Who will run it? How fast will the supplier respond to a breakdown?
  • Compare total cost, not just price. A cheaper plant that uses more power or needs frequent membrane changes can cost far more over five years.

Warning signs to avoid: no water test before quoting, no mention of energy recovery, ordinary steel parts on the seawater side, no spare parts stock, and no written water quality guarantee.

Operation, Maintenance and Brine Management

A seawater RO plant gives years of safe water only if it is run and cared for properly. Salt air, muddy water and power cuts are hard on equipment, so a simple routine makes a big difference.

Daily and weekly routine

WhenTask
Every dayCheck feed pressure, RO pressure, product flow and product TDS; record them in a logbook
Every dayCheck antiscalant tank level and dosing pump
Every dayCheck UV lamp is on and storage tank is clean and covered
Every weekBackwash media filters; check cartridge filter pressure drop
Every weekRinse the plant with fresh RO water before any long shutdown
Every monthTest product water for TDS, pH and bacteria
As neededClean RO membranes (CIP) when output falls or pressure rises by about 10–15%
Every 1–2 yearsReplace cartridge filters regularly, media and UV lamps as needed
Every few yearsReplace SWRO membranes based on performance

Tips that make membranes last longer

  • Never let the plant run with chlorine reaching the membranes.
  • Flush the membranes with fresh water when you stop the plant for more than a day.
  • Keep pre-treatment working well. Most membrane problems start with poor pre-treatment.
  • Protect the container from heat and salt spray. Electronics fail fast in hot, salty air.
  • Train at least two local operators, so the plant does not stop when one person is away.

What happens to the brine?

About half or more of the seawater that enters the plant leaves as brine, which is roughly twice as salty as the feed. Globally, seawater desalination plants produce more than 150 million m³ of brine per day, and 80% of it is discharged within 10 km of coasts (UN World Ocean Assessment). In Bangladesh, the UNDP has also raised the question of what happens to wastewater from coastal RO plants (Eco-Business).

Good practice for a mobile plant:

  • Return brine to the open sea or a large tidal channel, not to ponds, canals or farmland.
  • Use a diffuser or long outfall pipe so the brine mixes quickly.
  • Keep the brine outlet well away from the intake, so the plant does not suck back its own salt.
  • Never dump brine on soil. It will make the land saline, which is the very problem we are trying to fix.
  • Check whether your project needs Department of Environment clearance under the Environment Conservation Rules 2023, and follow discharge limits.

For sites where brine cannot go back to the sea, PureLife can advise on brine reduction and Zero Liquid Discharge (ZLD) options.

PureLife Mobile Seawater RO Desalination Plant Service

PureLife is a Dhaka-based water and wastewater treatment company that has worked in Bangladesh since 2012 and reports more than 100 completed plants. We serve over 900 home users and more than 100 corporate customers, including government offices, national and multinational companies, embassies, universities, international donor offices, hotels and airlines. Our completed projects include RO drinking water plants for schools, officers’ messes and residential complexes.

For mobile seawater desalination, our service covers the full journey, from the first water test to years of after-sales care.

Our service process

  1. Consultation and needs check. Tell us your location, number of users and how long you need water. Our consultancy team helps you define the right capacity.
  2. Water test and site survey. We review a lab test of your raw water and check intake, power, access and brine disposal options.
  3. Design and proposal. We design the pre-treatment, SWRO stage, post-treatment and mobility type (container, trailer or skid) and share a clear quotation with specifications.
  4. Supply and fabrication. We source quality equipment from trusted suppliers in Taiwan, China, India and Bangladesh, including membranes, FRP vessels, multiport valves (MPV), media, chemicals and control panels.
  5. Delivery and installation. We deliver anywhere in Bangladesh, install, connect and commission the plant on site.
  6. Testing and handover. We test product water against Bangladesh drinking water standards before handover.
  7. Operator training. We train your local staff to run daily checks, backwash, dosing and safe shutdown.
  8. After-sales service. Spare parts, membranes, media, chemicals and maintenance visits, with a customer support response time of under 6 hours.

Why choose PureLife

  • Experience since 2012 in RO, iron removal, WTP, ETP and STP projects across Bangladesh.
  • Full in-house range. Pre-treatment, RO, softening, disinfection and wastewater solutions from one team.
  • Nationwide service, from Dhaka to the coastal belt.
  • Fast support with a 24/7 help desk and response under 6 hours.
  • Guarantee. One year guarantee on drinking water plants.
  • Spare parts and consumables in stock: RO membranes, cartridge filters, resin, activated carbon, UV and dosing chemicals.

Contact PureLife

  • Phone: 01919-998881
  • Email: bdpurelife@gmail.com
  • Corporate office: House #36, Flat #B-1, Road #15, Sector #11, Uttara, Dhaka-1230
  • Contact page

Many seawater projects also need other treatment. Explore our related solutions and guides below.

Our plants and solutions

Purifiers for homes and offices

Helpful guides from our blog

More from PureLife

Frequently Asked Questions (FAQs)

1. What is a mobile seawater RO desalination plant?

It is a movable water treatment system that removes salt from seawater or saline water using reverse osmosis. All parts are built into a container, trailer or skid, so it can be delivered and started quickly at almost any coastal site.

2. How does seawater reverse osmosis work?

Seawater is filtered to remove mud and particles. A high-pressure pump then pushes it at about 55–70 bar through RO membranes. Water molecules pass through, but salt and most impurities are held back and leave as brine.

3. Is desalinated water safe to drink?

Yes, when the plant is well designed and maintained. The water must meet Bangladesh standards, including TDS below 1,000 mg/L and zero faecal coliform. Good plants add minerals back and disinfect the water with UV or chlorine before storage.

4. How much water can a mobile seawater RO plant produce?

It ranges from small portable units of a few hundred litres per hour to containerised plants of up to 2,000 m³ (2 million litres) per day. The right size depends on the number of users and the use of the water.

5. What is the price of a seawater RO plant in Bangladesh?

There is no fixed price. Cost depends on capacity, raw water quality, pre-treatment, mobility type, power system and materials. PureLife prepares a quotation after reviewing your water test and site needs. Call 01919-998881.

6. How much electricity does a seawater RO plant use?

A modern seawater RO plant uses about 3.75–4.5 kWh of electricity per cubic metre (1,000 litres) of fresh water. An energy recovery device lowers this a lot. Brackish water RO uses much less.

7. What is the difference between a brackish RO plant and a seawater RO plant?

Brackish RO treats moderately salty water at lower pressure, with higher recovery and lower power use. Seawater RO treats very salty water at about 55–70 bar, with stronger membranes and pumps. Using a brackish plant on seawater will not give safe water.

8. Can a mobile RO plant run on solar power?

Yes. Many coastal plants in Bangladesh run on solar power, with grid, battery or generator backup for cloudy days and nights. Solar-hybrid design is a good choice for off-grid villages, islands and chars.

9. How long does it take to install a mobile desalination plant?

A containerised or trailer plant is factory-built and tested, so on-site setup usually takes hours to a few days once intake, power and outlet lines are ready. A fixed plant can take many months.

10. What is the recovery rate of a seawater RO plant?

For seawater, a single-pass system usually recovers up to about 50%. That means about 1 litre of fresh water for every 2 litres of seawater. The rest leaves as brine.

11. What happens to the brine from a desalination plant?

Brine should go back to the open sea or a large tidal channel through a diffuser, far from the intake. It must never be dumped on soil or into ponds, as it makes land saline. Follow Department of Environment rules.

12. How often should RO membranes be replaced?

With good pre-treatment and regular cleaning, seawater RO membranes usually last several years. Replacement depends on feed water quality, operating hours and how well the plant is maintained. Rising pressure and falling output are signs that cleaning or replacement is needed.

13. Can a mobile plant treat flood water or river water too?

Yes. With proper pre-treatment, a mobile RO plant can treat seawater, brackish river water, pond water and flood water. This makes it very useful in cyclone and flood response, when many water sources are contaminated.

14. Which areas in Bangladesh need seawater desalination most?

The southwest and south coastal districts, such as Satkhira, Khulna, Bagerhat, Barguna, Patuakhali and Pirojpur, plus islands and chars like St Martin’s, Hatiya and Sandwip, and the Cox’s Bazar–Teknaf coast.

15. Can I rent a mobile desalination plant for a short project?

Renting or leasing is common worldwide for construction sites, events and disaster seasons. Ask PureLife about short-term options for your project and location.

16. Does RO water remove arsenic and iron too?

RO removes most arsenic, iron and many other dissolved contaminants. However, high iron must be removed before RO, or it will block the membranes. That is why some coastal sites need an iron removal stage first.

17. Who can operate a mobile RO plant?

A trained local operator can run daily checks. PureLife provides operator training at handover, plus after-sales support, spare parts and maintenance visits.

18. Does PureLife provide service outside Dhaka?

Yes. PureLife provides installation and after-sales service across Bangladesh, including coastal districts and islands.

Conclusion: Safe Water Where the Sea Meets the Land

Salinity in coastal Bangladesh is rising, spreading inland and reaching deep tube wells. Cyclones and tidal surges can wipe out freshwater in a single night. A mobile seawater RO desalination plant answers both problems: it turns the water that is already there into safe drinking water, and it can move to wherever the need is greatest.

The key to success is simple: test your water, size the plant correctly, choose seawater-grade parts with energy recovery, plan brine disposal, and keep a trained operator with good after-sales support.

Need a mobile seawater RO plant for your community, project, island, resort or factory? Contact PureLife today. Share your location, number of users and a water test (if you have one), and our team will recommend the right solution.

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.